According to the principle of centrifugal separation, nex solid-liquid separator is used to separate precipitated solids.

The unique internal acceleration movement produces high-speed rotating water flow, and then the group impurities in the water can be efficiently discharged. Nike is famous for its advanced design and unique performance, and its comprehensive indexes are higher than those of similar filtering equipment.

NEX can separate solid particles with a specific gravity of 3 μ m to 9 mm greater than that of liquid. In the non circulating system, the separation effect of 74 μ m solid can be more than 98%; in the circulating system, the separation effect of 40 μ m solid can also be 98%.

The single unit capacity of Nike JPX (L) series is 1-2895 cubic meters / HR, which can deal with the sewage with the content of suspended solids up to 25000mg / L, and can meet the requirements of water treatment in various harsh environments.

Nike advantages

The separator has no movable elements, no filter screen, filter element and other elements, so there is no wear, no maintenance; no backwashing, no maintenance and operation of the equipment.

Nike has advanced sewage and sewage final treatment method. The water content of discharged sewage is less than 80%, and zero liquid loss can be achieved.

It can be used in parallel or in series to meet different water quality requirements and flow.

It occupies a small area and can replace the water treatment equipment of sedimentation tank and other links, saving space. The vertical and inclined structures can be selected according to the field pipeline conditions and space restrictions.

Lakos solid-liquid separator can be used in almost any flow liquid system, especially in the following application cases.

Nozzle and small hole protection: avoid dirt accumulation, blocking or wearing holes, completely reduce downtime, reduce pipeline maintenance and parts replacement.

It can prevent the deposition of solids in the sedimentation tank or water reservoir: promote the cooling of cooling tower, quenching tank, parts washing tank, etc., eliminate the shutdown and routine maintenance due to solid deposition, and avoid the bacterial growth induced by solid deposition.

Fine filtration / extended water system life: discharge large solids in advance to reduce filter cartridge wear; extend the service life of filter parts; reduce maintenance, shutdown times and replacement cost of filter media.

Protect heat exchanger: control solid dirt, remove coarse sand and dirt deposits, maintain efficiency of exchange system, and avoid excessive energy loss.

Minimize consumption: extend liquid life by removing insoluble solids, concentrate and separate to remove (waste liquid), recycle or reuse, and reduce your environmental emission costs.

Lakos can satisfy even the most demanding system under any condition: even the most difficult situation can be solved.

Lakos has been successfully applied in all walks of life

Pretreatment of automobile painting station;

Food processing - recycling useful liquid and oil for fried food;

Cooling water system - heat exchanger protection, compressor protection, pump protection, open closed cycle system;

Chemical production - recycle and pre filter chemical liquid to minimize waste discharge;

Municipal Water - desanding of source water, pretreatment of waste water and improvement of water system;

Mechanical manufacturing and processing industry - recycling of cooling water for parts processing and metal processing, cleaning of waste from engine oil tank and recovery of debris;

Vehicle cleaning system - oil cleaning and chemical cleaning of buses, fishing boats, trucks and trains, and water recycling;

Mining - solid re extraction, liquid recycling;

Papermaking - reuse of water for papermaking;

Fuel filtration - injection engine oil, gasoline, kerosene;

Petrochemical Industry - filtration of water injection and brine, reuse of offshore oilfield and process liquid;

Heat supply, ventilation and air conditioning system - nozzle protection, keep the water system clean, the water tank free of accumulation, can control the growth of bacteria, reduce pollution, improve the heat exchange effect, and save energy.

Important metal processing - recovery of all kinds of metal waste from quenching system, nozzle dirt, rolling mill, etc..

1. Pressure gauge with small piston valve at inlet / outlet. It is included in the standard equipment, and the inlet / outlet are equipped with devices to control the flow rate range.

2. A solid bond. Provide a complete access to the upper part of the collection chamber, the acceleration tank and the internal separation barrel; two pieces.

3、 Vortex tube. Piping provided by lakos.

4. Precise connection path. Provide access to the collection room for inspection / maintenance.

5. Connect the shaft. When it is removed, space can be left to connect the close coupling into the separator, not included in the separator system, which can be purchased separately.

6. Manually operated isolation valve. Included in the standard equipment for maintenance of the automatic drain valve.

1. Pressure gauge with small piston valve at inlet / outlet. It is included in the standard equipment, and the inlet / outlet are equipped with devices to monitor the flow rate range.

2. Check / drain plug. 1 / 2 inch inner hole; provide access to the upper part of the collection chamber to check the groove area; drain the liquid on the upper part of the collection chamber if necessary.

3. A solid bond. Provide a complete access to the upper part of the collection chamber, the acceleration tank and the internal separation barrel.

4. Rings. Easy to install.

5. Connect the shaft. When it is removed, space can be left to connect the close coupling into the separator, not included in the separator system, which can be purchased separately.

6. Hand hole inspection port. Provide access to the collection room.

7. Vortex tube. Piping provided by lakos.

8. Manually operated isolation valve. Included in standard equipment for maintenance of automatic drain valve

。

1. Pressure gauge with small piston valve at inlet / outlet. It is included in the standard equipment, and the inlet / outlet are equipped with devices to monitor the flow rate range.

2. Check / drain plug. 1 / 2 inch inner hole; provide access to the upper part of the collection chamber to check the groove area; drain the liquid on the upper part of the collection chamber if necessary.

3. A solid bond. Provide a complete access to the upper part of the collection chamber, the acceleration tank and the internal separation barrel.

4. Rings. Easy to install.

5. Connect the shaft. When it is removed, space can be left to connect the close coupling into the separator, not included in the separator system, which can be purchased separately.

6. Hand hole inspection port. Provide access to the collection room.

7. Vortex tube. Piping provided by lakos.

8. Manually operated isolation valve. Included in the standard equipment for maintenance of the automatic drain valve.

1. Pressure gauge with small piston valve at inlet / outlet. It is included in the standard equipment, and the inlet / outlet are equipped with devices to control the flow rate range.

2. Vortex tube. Piping provided by lakos.

3. Manually operated isolation valve. Included in the standard equipment for maintenance of the automatic drain valve.

1. Pressure gauge with small piston valve at inlet / outlet. It is included in the standard equipment, and the inlet / outlet are equipped with devices to control the flow rate range.

2. Check / drain plug. 1 / 2 inch inner hole; provide access to the upper part of the collection chamber to check the groove area; drain the liquid on the upper part of the collection chamber if necessary.

3、 Vortex tube. Piping provided by lakos.

4. Hand hole inspection port. Provide access to the collection room.

5. Rings. Easy to install.

6. Manually operated isolation valve. Included in standard equipment for maintenance of automatic drain valve

。

Lakos can also be specially manufactured for special users. The detailed description and options are as follows:

1. Maximum pressure rating: 150 psi (1055kpa); higher pressure can also be used.

2. Pressure loss range: 4.5-12 psi (32-85kpa).

3. Inlet and outlet flange: 150 pound (1MPa) flange; ANSI American national standard; can also use liter interface DIN (German Standards Association), or connect BSP pipe, British standard pipe thread and other types of pipe.

4. Material details: the standard type is carbon steel; others are special materials; stainless steel, reinforced agglomerated ester Fiberglass (FRP), Monel alloy composite steel, AR steel (wear-resistant steel), low alloy steel, PVC (PVC), PVC engineering plastics (KXL Series) and materials allowed by the U.S. Department of engineering. In addition, the manufacturer can also customize according to customer requirements.

5. Special coating: epoxy resin, nickel, scotchkotetm, kanigentm, techthanetm and other special coating.

6. Parts treatment: electropolishing, electroplating, high temperature heat treatment, high quality primer.

7. Other accessories: low or vertical external decoration, high pressure parts, package / multi-stage braking system, etc.

8. Pretreatment system (lower part): completely separate the liquid / solid, and queue the solid regularly, with automatic pressure control and dry slag queuing through vacuum (no water loss).

You can completely separate the solid from your process liquid through lakos, and line up the dry slag in a centralized way; you can also separate the desired solid from the process liquid.

The automatic purification machinery and other auxiliary devices can effectively separate the solid from the lakos separator; in particular, the required solid collection system can be pre selected in a planned way to meet the demanding requirements of customers.